An effective way to solve the temperature rise of PCB in PCB design, these factors are often related and dependent on each other in one and the system. Most factors should be analyzed according to the actual situation. Only for a specifIC actual situation can the PCB temperature rise and power consumption and other parameters be calculated or estimated correctly.

1. PCB proofing production heats up by selecting PCB boards with good heat dissipation

   
   

At present, the widely used PCB boards are copper clad/epoxy glass cloth substrate or phenolic resin glass cloth substrate, and there are a few paper based copper clad boards. Although these substrates have excellent performance and processing performance, they have poor heat dissipation. As a heat dissipation way for high heating elements, it is almost impossible to rely on the resin of PCB itself to conduct heat, but to dissipate heat from the surface of the element to the surrounding air. However, as the products have entered the era of miniaturization, high-density installation and high heating assembly of components, it is not enough to rely only on the surface of components with very SMAll surface area for heat dissipation. At the same time, due to the large use of surface mounted components such as QFP and so on, a large amount of heat generated is transferred to the pcb board. Therefore, the best way to solve the heat dissipation is to improve the heat dissipation capacity of the PCB itself that directly contacts the heating elements, and transmit or distribute it through the PCB board.

2. During PCB design, high heating components are added with heat sink and heat conduction plate

When there are a few components in the PCB with large heating capacity (less than 3), a radiator or heat transfer tube can be added to the heating components. When the temperature cannot be reduced, a radiator with a fan can be used to enhance the heat dissipation effect. When there are many heating devices (more than 3), large heat dissipation cover (plate) can be used. It is a special radiator customized according to the position and height of the heating devices on the PCB board, or different component high and low positions can be picked out on a large flat panel radiator. Buckle the heat shield onto the element surface as a whole, and contact each element to dissipate heat. However, due to the poor consistency of PCB components during assembly and welding, the heat dissipation effect is not good. Usually, a soft thermal phase change heat conduction pad is added on the surface of the components to improve the heat dissipation effect.

3. For equipment cooLED by free convection air, it is better to arrange (or other devices) in longitudinal or transverse direction.

4. Adopt reasonable wiring design to realize heat dissipation

Because the resin in the sheet has poor thermal conductivity, and the copper foil lines and holes are good conductors of heat, improving the copper foil residual rate and increasing the thermal conductivity holes are the main means of heat dissipation.

To evaluate the heat dissipation capability of a PCB, it is necessary to calculate the equivalent thermal conductivity (9 eq) of a composite material composed of various materials with different thermal conductivity - insulating substrate for PCB during PCB design.

5. The components on the same printed board shall be arranged in zones as far as possible according to their calorific value and heat dissipation degree. The components with low calorific value or poor heat resistance (such as small signal transistors, small-scale integrated circuits, electrolysis, etc.) shall be placed at the top (entrance) of the cooling air flow, and the components with high calorific value or good heat resistance (such as power transistors, large-scale integrated circuits, etc.) shall be placed at the bottom of the cooling air flow.

6. In the horizontal direction, high-power devices shall be arranged as close to the edge of the printed board as possible to shorten the heat transfer path; In the vertical direction, high-power devices shall be arranged as close as possible to the top of the printed circuit board, so as to reduce the impact of these devices on the temperature of other devices during operation.

7. The heat dissipation of the printed circuit board in the equipment mainly depends on the air flow, so the air flow path shall be studied during the design, and the device or printed circuit board shall be reasonably configured. When air flows, it always tends to flow in a place with small resistance. Therefore, when configuring components on the PCB, it is necessary to avoid leaving a large space in a certain area. The configuration of multiple printed circuit boards in the whole machine should also pay attention to the same problem.

8. The devices sensitive to temperature should be placed in the area with the lowest temperature (such as the bottom of the equipment), and should not be placed directly above the heating devices. Multiple devices should be staggered on the horizontal plane.

9. Place the device with the highest power consumption and heat generation near the best heat dissipation position. Do not place the components with high heat generation on the corners and surrounding edges of the printed board, unless there is a heat sink near it. When designing the power resistance of PCB, select larger components as far as possible, and make it have enough heat dissipation space when adjusting the layout of PCB.

10. RF power amplifier or LED PCB adopts metal base plate.

11. Avoid the concentration of hot spots on the PCB, distribute the power evenly on the PCB as much as possible, and keep the PCB surface temperature performance uniform and consistent. It is often difficult to achieve strict uniform distribution in the design process, but the area with too high power density must be avoided to avoid the occurrence of hot spots that affect the normal operation of the entire circuit. If conditions permit, it is necessary to conduct thermal efficiency analysis of printed circuit. For example, the thermal efficiency index analysis software module added to some professional PCB design software can help designers optimize PCB design.